Home > Error Code > Jacuzzi Error Codes

Jacuzzi Error Codes


This setting is not user-programmable. The J-365 jacuzzi hot tub hot tub spa is a 6 person hot tub. The J- 325 features two deep bucket seats and one deep lounge. What do I do? this contact form

System will restart when temp. Join 6 other subscribers Email Address Top Posts & Pages Jacuzzi Hot Tubs Error Codes & Information Hot Tub Filters - When To Clean & When to Replace Beachcomber Hot Tubs FL2 = Pressure switch problem. If itwill not reset, check for clogged filters.

Jacuzzi Error Code Fl1

Filter and circulation pump is activated and the heater is deactivated DO NOT GET INTO THE WATER. BLB (Flashes in between water temperature and “blb”) Indicates that the Jacuzzi Hot Tubs needs a new UV bulb. Q: My control panel reads the error code "---". Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled.

One sensor has detected 118º F at heater. dr = Inadequate water detected in heater. Wait three seconds and then restart the spa to see if error clears up. Vita Spa Error Codes In both cases, the spa heater will deactivate.

DO NOT GET INTO THE WATER. Jacuzzi Error Code 616 Carlsbad: (760) 431-7727 | San Diego (858) 675-7727 Find Your Perfect Hot Tub J-500 Collection J-585™ Seats: 5-7 Jets: 52 J-575™ Seats: 5-6 Jets: 53 J-400 Collection J-415™ Seats: 2-3 Jets: Remember, the cleanest spas have their filters replaced every 18-24 months. It has disabled itself to prevent further damage.

Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when How To Fix Flo Error Hot Tub Contact the dealer or service technician if the problem continues. Reset the countdown timer when finished. If buzzing sound or lack of sound is detected, cut off the water to the hot tub – may indicate that pump is notproperly primed.

Jacuzzi Error Code 616

The spa filters need to becleaned or replaced. BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" Jacuzzi Error Code Fl1 Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled. Balboa Hot Tub Error Codes Communication Error Communication between circuit board and control panel is malfunctioning.

A: When you see this on your control, rest assured, nothing is wrong. http://rsmasters.net/error-code/ir3300-error-codes.html All Rights Reserved. Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Email check failed, please try again Sorry, your blog cannot share posts by email. %d bloggers like this: Making the most of your Backyard Heaven! Jacuzzi Error Code Cf

  1. Condition can cause injury or damage to spa and its components.
  2. Open Sensor (Hi-Limit) The hi-limit temperature sensor is malfunctioning; heater is taken offline automatically when this happens.
  3. Heater disabled but the spa is operational.PSoC = Pressure switch open with circulating pump.PSoL = Pressure switch open with low pump.PSoH = Pressure switch open with high pump.ToE = Time out

The Jacuzzi Spa J-465 hot tub spa is a 5 person hot tub. d) Replace the filter cartridge and verify the solution worked.4. No action needed. navigate here OHS = Overheat.

Do not attempt to service on your own. Marquis Spa Error Codes HomeTestimonialsBlogIndustry LinksPolicies, Warranties and DisclaimersService Area-Contact UsSpas / Hot Tubs & Swim SpasFilter Cartidge Cleaning - Home remedySterilizing before UsageProperly Closing-WinterizingError Codes-Digital or Blinking Indicator LightWinter Trouble? Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog".

c) Get an assistant to help turn the water on for 30 seconds.

DO NOT GET INTO THE WATER. The Jacuzzi Spa J-325 hot tub spa is a 3-4 person hot tub. This condition does not kick in until the water temperature climbs to 95°F (35°C). Jacuzzi Error Code Fl2 ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement

Power on the spa must be cycled before the heater will function again. Open Sensor Means temperature sensor is malfunctioning; heater is taken offline automatically when this happens. Purchase new UV bulb from dealer and reset countdown timer. his comment is here Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat.

Contact a Jacuzzi hot tubs dealer or a service technician. – – – The water temp has raised above acceptable safety limits and triggered the safety “Watchdog” program of the spa Jacuzzi Hot Tubs J-300 Error Conditions/ Error Messages Message Meaning Action Required COL This only occurs when spa is in Economy mode and indicates a cool condition where temps have dropped Replace UV bulb (you can get one from your authorized Jacuzzi dealer). The Cover Guy says: Hi Angela, you may want to look at our hot tub...

Heater will automatically turn on when this happens and stay in this mode until water temperature reaches 15 degrees below set temperature. You can often determine the make of the control system by looking inside the spa's equipment area. Heater is deactivated. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.

Add water if needed.2. No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. Do not enter the spa. Turn your breaker off.

This setting is not user-programmable.